NB48.4 1/8 4WD Competition Nitro Buggy Kit


1 in stock

SKU: TKRTKR8300 Categories: ,



1/8 scale Glow Powered, Radio Controlled, 4WD Competition NB48.4 Buggy Kit from Tekno RC.

**Engine Shown in Photo is NOT Included.**


  • Chassis: CNC machined hard anodized lightened 7075 aluminum,
    0.16″ (4mm) thick, short overhang for better bump handling and
    jump landing, adjustable brace system
  • Drive: Four wheel with CV driveshafts and captured pins on wheels
  • Clutch: Adjustable, four 7075 aluminum shoes
  • Clutch Bell: 13T CNC machined steel, CNC machined flywheel
  • Fuel Tank: 4.2oz (125cc), IFMAR legal integrated filter/clunk with
    external nipple
  • Differentials: Three fluid filled adjustable lightweight diffs
  • Suspension: Fully adjustable long travel, adjustable front arm
    sweep and angle, front and rear sway bars, captured outer front and
    rear hinge pins, adjustable hinge pin braces, narrow high roll
    center rear hubs, new bearing supported spindle/carrier with
    updated geometry and enhanced durability
  • Steering: Ball bearing equipped, narrow pivot steering posts,
    adjustable steering stops for precise travel setting, new
    bellcranks, with optional solid right bellcrank (no servo saver)
    for increased steering response
  • Shocks: 16mm bore CNC machined hard anodized threaded aluminum
    bodies, 4mm hardened steel polished shock shafts, CNC machine
    tapered pistons, CNC aluminum shock caps, preload adjusters and
    cartridge caps, Triple Guide Design for reduced shaft deflection,
    new clamping spring perches w/captured shock boots, options for
    vented cap, emulsion, or standard shock configurations
  • Front Shock Tower: 0.24″ (6mm) CNC machined 7075 aluminum
  • Rear Shock Tower: 0.20″ (5mm) CNC machined 7075 aluminum
  • Engine Mount: Adjustable
  • Brakes: CNC machined steel disc with semi-metallic pads
  • Wing: New high downforce Wing, adjustable LCG lightweight mount
  • Radio Tray: Integrated with right mud guard allowing receiver &
    battery to sit on chassis for lowest CG possible
    Throttle Control: CNC machined assembly riding on ball bearings
  • Spur Gear: 48T steel
  • Ackerman: Adjustable, Ackerman describes the effect of the inside
    front wheel turning faster than the outside front wheel during
    turns, CNC aluminum Ackerman plate rides on precision ball bearings
  • Caster: Adjustable, caster/toe-in refers to the angle of the front
    suspension when viewed from the side of the car in relation to
    the chassis
  • Camber: Adjustable front and rear, camber refers to the angle of the
    tops of the tires from vertical when viewed from front or behind


NB48.4 Buggy Kit, Shock and Diff Oil, Threadlock, clear Body, 13T
Clutch Bell, 48T Spur Gear, High-Downforce Wing, Decals, Shock and
Diff Oil, Instructions


Radio: 2-3ch with high-torque/speed steering & throttle servos
Engine: .21 cu in (3.4cc) glow engine with tuned pipe
Receiver Battery: Hump configuration
Tires and Wheels: 1/8 scale buggy
Starter box & glow igniter
Polycarbonate safe spray or brush on paint
Building and track equipment


Length: 17.1″ (435mm) without wing
Width: 12-12.2″ (306-310mm)
Wheelbase: 12.7-13.2″ (323-335mm) adjustable
Dry Weight: 7.17lb (3260g), varies depending on equipment
Diff Ratio: F/R-12/39t, center-48t
RX Battery Box Dimensions: 2.3 x 1.4 x 1.3″ (58.5 x 36 x 34.5mm)
Length: 13.4″ (340mm)
Width: 7.2″ (183mm)
Height: 4″ (102mm)

Additional information

Weight 8 lbs


There are no reviews yet.

Be the first to review “NB48.4 1/8 4WD Competition Nitro Buggy Kit”