• R/C Madness
  • Products
  • R/C Madness Products
  • RCM Conversion Kits
  • RC Madness BL5 Version 2 Conversion for the Losi 5IVE-T(BATTERY TRAY HOLDERS ANODIZED BLACK. LIMITED RUN)
  • RC Madness BL5 Version 2 Conversion for the Losi 5IVE-T(BATTERY TRAY HOLDERS ANODIZED BLACK. LIMITED RUN)

    $279.99

    Out of stock

    Be notified when this product is back in stock!

    SKU: RCMBL5 Categories: ,
    Share this product

    RC Madness BL5 Version 2 Conversion for the Losi 5IVE-T

    RC Madness BL5 Version 2 Conversion for the Losi 5IVE-T

    The RC MADNESS brushless conversion for the Losi 5ive represents countless hours of painstaking design and engineering. Our goal was to bring you the strongest, fastest, best handling conversion available for the 5ive, period.

    Why spend as much as $2000 on the latest engine, pipe and clutch when you can have more power without the noise, tuning and hassle of buying and mixing gas. Two cycle engines only make their rated horsepower from about 12,000 – 16,000 rpm. Our electric conversion makes 10hp over the entire rpm range up to 35,000rpm!
    This is the new, improved Version 2 conversion kit! The motor mount has been redesigned for use with the Neu 2028 motor as well as the Lehner LMT 3080/6 LK Motor!

    Features

    • -The only 1/5th brushless setup on the market that gives you the option of two speed controllers and up to 12S lipo! Thats 50 volts! Nothing else even comes close.
    • -We retained factory mechanical disc braking, allowing for front / rear brake bias and improved control and handling.
    • -Mechanical brakes eliminate motor and esc stress and allows cooler operating temperature in all conditions.
    • -Forget thin cast aluminum plates and rear motor supports. Our motor mount is CNC milled from T-6061 aircraft aluminum is ONE INCH THICK yet is very light weight. The motor sits inside the block a full 20mm and uses the stock mounting locations and gear mesh inserts to make installation a snap.
    • -Stock chassis requires no modifications or drilling. Installation takes less than 20 minutes.
    • -Optimized weight distribution. Batteries set as close to center and as far forward as possible resulting is higher corner speed, improved steering and incredibly predictable control.
    • -We built a battery tray specific to the 5ive from 7075 aluminum and 3mm carbon fiber plate. The straps are long and anchored and the mount is fully adjustable. No 1/8th conversion parts were carried over to the 5ive.
    • -Motor is mounted just 3mm from chassis for the lowest Center of Gravity possible. Lower than the factory gas setup!
    • – Conversion is fully compatible with all aftermarket and optional chassis braces

    Conversion includes:

    • NEW Version 2 Bilelt aluminum motor mount
    • Carbon Fiber battery tray
    • 4 high strength velcro battery straps
    • 8 billet 7075 battery strap mounts
    • Battery tray mounting blocks and spacers (6061 billet cnc machined)
    • 16 tooth Castle pinion gear
    • 4mm motor mount cap head screws for securing motor to mount.

    *MOTOR AND ESC ARE NOT INCLUDED

    Weight3 lbs

    You may also like…

    • Mamba XL X 34V ESC 20A + 2028 800kV MotorMamba XL X 34V ESC 20A + 2028 800kV Motor

      Mamba XL X 34V ESC 20A + 2028 800kV Motor

      $369.99
      Mamba XL X 34V ESC 20A + 2028 800kV Motor Castle Creations 2028 800kV Sensorless Brushless Motor and Mamba XL…
      Add to cart